6" to 12" ID x 0.210" CS Buna-N 70 Vulcanized O-Ring
Dimensions: 6" to 12" ID x 0.210" (5.33mm) CS, spliced and vulcanized to the exact ID you ordered.
The 6" to 12" ID x 0.210" CS Buna-N 70 Vulcanized O-Ring is a custom O-Ring made from 0.210" (5.33mm) cross-section Buna-N (Nitrile, NBR) cord. It is spliced and vulcanized to any inside diameter you order from 6" to 12" (150.00mm to 304.80mm). The O-Ring Store LLC makes every ring to the size you order, verifies it with an Olypsys® scan and replaces it if the joint or the size is ever wrong.
Get the exact O-Ring your gland needs without waiting weeks on a mold. We cut Buna-N 70 cord to length, splice it and vulcanize the joint into one continuous ring at any ID from 5" to 12". There is no tooling to pay for, so one O-Ring is as easy to order as a hundred. Maintenance crews use these rings to get a pump, cylinder or tank lid back in service fast. Engineers and OEMs use them when a design calls for a size nobody molds.
The Best Vulcanized O-Rings in the World, and We Prove It
We make it to the size you order. Then we prove it.
The Best Vulcanized O-Rings on the Planet. Period. Anybody can say it. We prove it, O-Ring by O-Ring, every order.
Most shops "check" a large vulcanized ring by wrapping a pi tape around it and calling it good. That reading depends on whoever's holding the tape. Pull a little hard and the O-Ring stretches bigger. Go easy and it reads small. Then somebody says "Yep, looks right," and that's your quality control. That's it.
We looked at that and said no way. Not on our watch, not with our name on it.
Up to 48" (1219mm) ID: Tolerances optically measured, proven on paper.
Every vulcanized O-Rings up to 48" OD is built to, ±0.80% to ±1.00% tolerances. Tighter than most shops even bother to quote. Then every ring gets a hands-on visual inspection and goes on our Olypsys® Large Format Optical Measurement Grid. On orders up to 100 pieces, we measure every single O-Ring. On runs over 100 pieces, we scan a 10 percent sample pulled straight from the lot. The O-Ring lies flat and relaxed on the grid, so nothing gets stretched and nobody's thumb is on the scale. You get the Olypsys® Measurement Verification Report with the measured ID, OD, and cross-section. Real numbers, on paper, in your hands before that ring ever gets near your machine. Try finding another shop that does that.
Over 48" OD: Class 3 tolerances, visually inspected, built for the big stuff.
Rings larger than 48" OD are built to Class 3 tolerances, ±1.20% to ±1.50%, and every one gets a visual inspection before it leaves our building. Big O-Rings for big equipment, made right the first time.
And we guarantee it. 100 percent. The joint AND the size.
If a splice ever lets go, we replace it. If an O-Ring isn't the size you ordered, we replace it. No fine print, no runaround, no "well, technically." Two guarantees, zero weasel words. Other shops tell you their joints are good and hope you never find out otherwise. We send you the proof, stand behind every splice and every dimension, and put The O-Ring Store name right on it.
You can buy a vulcanized O-Ring anywhere. You can only buy one this tight, this well documented, and 100 percent guaranteed on both the joint and the size from us.
The best vulcanized O-Rings in the world. Measured. Proven. Guaranteed.
Operating Temperature: -40 to +250F (-40 to +121C)
Material and Performance
Buna-N, also called Nitrile or NBR, is the workhorse elastomer for oil and fuel service. At 70 durometer Shore A it is firm enough to resist extrusion in most static glands and soft enough to seal on ordinary machined surfaces. The standard color is black. Buna-N 70 has good tensile strength, strong abrasion resistance and low compression set. It also stays dimensionally stable, which matters on a large ring that has to hold its shape in the groove.
- Excellent resistance to: petroleum oils, fuels (gasoline and diesel), hydraulic fluids (petroleum-based), mineral oils, silicone greases and oils, water, ethylene glycol and LP gases
- Limited capability with: dilute acids and long-term sunlight (UV) exposure
- Not compatible with: strong acids, ozone, ketones (acetone and MEK), halogenated hydrocarbons (carbon tetrachloride), phosphate ester hydraulic fluids (Skydrol), automotive brake fluid, nitro hydrocarbons and aromatic hydrocarbons
Sizes and Measurements
- Inside Diameter Range: 6" to 12" ID (127.00mm to 304.80mm), made to the exact ID you order
- Cross-Section: 3/16" nominal, 0.210" actual (5.33mm)
- Metric Sizes: any mm ID from 150.00mm to 304.80mm on 5.33mm cord
- Construction: extruded Buna-N cord, spliced and vulcanized into one continuous ring
- Cross-references: AS568-353 (4.975" ID / 126.37mm) through AS568-381 (11.975" ID / 304.17mm), all 0.210" (5.33mm) CS; ISO 3601 5.33mm CS series. These match on size only. A vulcanized ring replaces the molded dash size in the same gland.
Applications and Use Cases
The Buna-N 70 Vulcanized O-Ring seals hydraulic cylinders, pump housings, valve bodies, tank and hatch covers, filter housings, gearbox covers and large flanges in oil, fuel, hydraulic fluid and cold water service. It is a go-to for MRO emergencies, when a machine is down and the original seal is an odd size or years out of production. One honest note most suppliers leave out: a vulcanized joint is at its best in static and slow-moving seals. If you run a high-cycle reciprocating rod or piston and a standard molded AS568-3xx size fits your gland, buy the molded ring. Call us and we will tell you straight which one fits your job.
Key Specifications
- Material: Buna-N (Nitrile, NBR)
- Durometer: 70 Shore A
- Color: Black
- Temperature Range: -40 to +250F (-40 to +121C)
- Size: made to the ID you order, verified by Olypsys® scan
- Inspection: every O-Ring scanned on orders up to 100 pieces; 10 percent sample scan on orders over 100 pieces
- Documentation: Olypsys® Measurement Verification Report with measured ID, OD and CS
- Guarantee: 100 percent; any failed joint or wrong-size ring is replaced
- Lead Time: up to 24 pieces about 2 to 5 days ARO; 25 to 100 pieces about 5 to 10 days ARO; over 100 pieces about 10 to 15 days ARO (depends on cord stock)
Why Buy from The O-Ring Store LLC
The O-Ring Store LLC is an ISO 9001:2015 certified distributor with USA-based stock, and most in-stock items ship the same day. Nobody in the world does vulcanized O-Rings better than we do, and we prove it on every order with an Olypsys® scan report in your hands. Every ring is made to the size you order and every joint is guaranteed, so buying from us carries zero risk. You also get full lot traceability and documentation on request, plus technical help from people who have spent decades sizing and specifying seals. Use our O-Ring Cord Cut-Length Calculator to check your numbers, or send us the gland size and we will figure it out with you. We make getting O-Rings easy!
Frequently Asked Questions
Q: How do I know a custom vulcanized O-Ring will be the size I ordered?
A: The O-Ring Store LLC makes every 6" to 12" ID x 0.210" CS Buna-N 70 Vulcanized O-Ring to the size you order and proves it with an Olypsys® scan. Orders up to 100 pieces get every single O-Ring scanned, and orders over 100 pieces get a 10 percent sample scan. You receive the Olypsys® Measurement Verification Report, and if a ring is not the size you ordered, we replace it.
Q: Is a spliced and vulcanized Buna-N O-Ring as strong as a molded O-Ring?
A: A 0.210" (5.33mm) CS Buna-N 70 vulcanized O-Ring from The O-Ring Store LLC carries a 100 percent joint guarantee and performs like a molded ring in static seals and slow-moving service. For high-cycle reciprocating rods and pistons, a molded AS568-353 through AS568-381 O-Ring is the better choice when one of those sizes fits your gland. The vulcanized ring wins when you need an odd size, one piece or a fast turnaround.
Q: What temperatures and fluids can a Buna-N 70 vulcanized O-Ring handle?
A: A Buna-N 70 vulcanized O-Ring seals from -40 to +250F (-40 to +121C). It has excellent resistance to petroleum oils, gasoline, diesel, petroleum-based hydraulic fluids, silicone greases and water. Do not use it with ketones like acetone or MEK, Skydrol, brake fluid, strong acids or ozone.